TPV
Brief introduction:
Thermoplastic vulcanizate (TPV), which consists of a polyolefin phase (PP) with a dynamically cured EPDM phase, is closely dispersed in the PP matrix which gives rubber-like properties and has the advantage of thermoplastic processing techniques.
The final blend morphology always consists of cross-linked, micron sized elastomer particles dispersed in a polymer matrix.Because of the strong mechanical shearing and the chemical cross-linking by crosslinking agent, the rubber phase is cut into a large number of micron-scale cross-linked rubber particles dispersed in the thermoplastic resin matrix in the continuous phase thermoplastic resin matrix.
|
|
|
IC55A |
IC65A |
IC7A |
IC85A |
IC40D |
IC50D |
IC55A-01 |
IC65A-01 |
IC75A-01 |
|
Hardness Shore A/D |
ASTMD2240 |
55A |
65A |
75A |
85A |
40D |
50D |
55A |
65A |
75A |
|
Density g/cm3 |
ASTMD792 |
0.95 |
0.96 |
0.96 |
0.97 |
0.97 |
0.95 |
0.95 |
0.95 |
0.95 |
|
Tensilestressat 100% , MPa |
ASTMD412 |
2.4 |
2.9 |
3.4 |
5.6 |
8.5 |
11.5 |
2.4 |
2.9 |
3.4 |
|
Tensile strength, MPa |
ASTMD412 |
4.4 |
6.0 |
8.0 |
13.5 |
18.5 |
20 |
4.5 |
6.2 |
8.5 |
|
Elongation at break,% |
ASTMD412 |
406 |
414 |
462 |
464 |
502 |
500 |
410 |
425 |
460 |
|
Tear strength, KN/m |
ASTMD624 |
21.2 |
25.0 |
33.1 |
55.0 |
78.0 |
98 |
22.5 |
28.9 |
35.2 |
|
Compression set , 22h/70°C,% |
ASTMD395 |
31.9 |
32.5 |
35.0 |
38.2 |
42.0 |
45.0 |
31.9 |
32.5 |
35.0 |
|
Brittle temperature, °C |
ASTMD746 |
-60 |
-60 |
-60 |
-55 |
-50 |
-50 |
-60 |
-60 |
-60 |
|
Processing temperature, °C |
170-190 |
|||||||||
Noted:
▲ Use PP or PE to clean the material before processing, and the raw material is dried at 90 ℃ -100 ℃ for 1.5 to 2 hours;
▲ Dye with PP or PE grade masterbatch, add at a rate of 2-3%;
▲ The processing temperature is between 165 ℃ and 200 ℃, and the highest temperature should not exceed 200 ℃;
▲ The length-diameter ratio of the equipment during extrusion processing should not be less than 25;
▲ Processing parameters such as temperature, pressure, and injection speed must be carefully adjusted during vertical injection.
Remarks: The above indicators are for reference. If there are special requirements on certain performances, our company can customize them individually according to customer needs. For details, please call us.
keywords: TPV
classification: Product
Brief introduction:
Thermoplastic vulcanizate (TPV), which consists of a polyolefin phase (PP) with a dynamically cured EPDM phase, is closely dispersed in the PP matrix which gives rubber-like properties and has the advantage of thermoplastic processing techniques.
The final blend morphology always consists of cross-linked, micron sized elastomer particles dispersed in a polymer matrix.Because of the strong mechanical shearing and the chemical cross-linking by crosslinking agent, the rubber phase is cut into a large number of micron-scale cross-linked rubber particles dispersed in the thermoplastic resin matrix in the continuous phase thermoplastic resin matrix.
|
|
|
IC55A |
IC65A |
IC7A |
IC85A |
IC40D |
IC50D |
IC55A-01 |
IC65A-01 |
IC75A-01 |
|
Hardness Shore A/D |
ASTMD2240 |
55A |
65A |
75A |
85A |
40D |
50D |
55A |
65A |
75A |
|
Density g/cm3 |
ASTMD792 |
0.95 |
0.96 |
0.96 |
0.97 |
0.97 |
0.95 |
0.95 |
0.95 |
0.95 |
|
Tensilestressat 100% , MPa |
ASTMD412 |
2.4 |
2.9 |
3.4 |
5.6 |
8.5 |
11.5 |
2.4 |
2.9 |
3.4 |
|
Tensile strength, MPa |
ASTMD412 |
4.4 |
6.0 |
8.0 |
13.5 |
18.5 |
20 |
4.5 |
6.2 |
8.5 |
|
Elongation at break,% |
ASTMD412 |
406 |
414 |
462 |
464 |
502 |
500 |
410 |
425 |
460 |
|
Tear strength, KN/m |
ASTMD624 |
21.2 |
25.0 |
33.1 |
55.0 |
78.0 |
98 |
22.5 |
28.9 |
35.2 |
|
Compression set , 22h/70°C,% |
ASTMD395 |
31.9 |
32.5 |
35.0 |
38.2 |
42.0 |
45.0 |
31.9 |
32.5 |
35.0 |
|
Brittle temperature, °C |
ASTMD746 |
-60 |
-60 |
-60 |
-55 |
-50 |
-50 |
-60 |
-60 |
-60 |
|
Processing temperature, °C |
170-190 |
|||||||||
Noted:
▲ Use PP or PE to clean the material before processing, and the raw material is dried at 90 ℃ -100 ℃ for 1.5 to 2 hours;
▲ Dye with PP or PE grade masterbatch, add at a rate of 2-3%;
▲ The processing temperature is between 165 ℃ and 200 ℃, and the highest temperature should not exceed 200 ℃;
▲ The length-diameter ratio of the equipment during extrusion processing should not be less than 25;
▲ Processing parameters such as temperature, pressure, and injection speed must be carefully adjusted during vertical injection.
Remarks: The above indicators are for reference. If there are special requirements on certain performances, our company can customize them individually according to customer needs. For details, please call us.
DOWREN NEW MATERIAL (HENAN) CO.,LTD
TELL：Selina.Liu +86-0393-8993626 / +86 18137458807
ADD：150 meters north of the intersection of Zhongyuan Road and Pushang Road, Puyang City,Henan Province
EMAIL：dowren@dowren.com
WhatsApp (+86 18137458807)